Gugusse Compact

start - [Welcome!]

meantux (meantux@undisclosed.example.com) — 2026-04-25T15:51:03-0400

Welcome! This website is being updated all the time. Check often for updates! Well, I haven't updated it in a while, (although my collaborator Al might have updated a few things here and there more often than I), but the reason is that I'm too busy using my 2 Gugusses for my

disclaimer

meantux (meantux@undisclosed.example.com) — 2026-04-25T15:43:53-0400

DISCLAIMER Or why you shouldn't get into this project. * This is a lot of work to build; print, sand, screw, sand again, glue, solder, configure and adjust. Depending on your skills and experience I believe it would take 1 to 2 weeks of printing and then at least 20 hours (more like 40) of assembling.

set_up_your_raspberry_pi

al (al@undisclosed.example.com) — 2025-12-01T14:20:10-0400

Set Up Your Raspberry Pi, and Load the Gugusse 2.0 Software for use with the New 3.1 PCB Follow these instructions to configure your system with the new 3.1 PCB Detailed instructions are available here: [OS and Software Install 3.04.pdf] - NEW VERSION 12/2025!

os_and_software_install_3.04.pdf - created

al (al@undisclosed.example.com) — 2025-12-01T14:15:10-0400

operation_instructions

al (al@undisclosed.example.com) — 2025-11-19T09:59:00-0400

Go Back SOFTWARE INSTRUCTIONS INSTALLATION [OS & Software Installation Guide Version 3.04] - NEW VERSION 12/2025! Operation Guides [ Gugusse Compact Usage Guide Version 1.1 (New 2/25)] OPERATION * Load a film * adjust camera position * perform capture POST PROCESSING * stabilize, adjust and crop with BlackMagick Fusion software * extract audio from the pictures with aeo-light

build_your_own_electronic_board

al (al@undisclosed.example.com) — 2025-11-05T11:40:49-0400

Building the Gugusse 3.1 PCB You're going to need an empty Gugusse 3.1 Printed Circuit Board to start. These can be ordered from any company that produces PCBs in small quantities. The files you need are called Gerber Files and the PCB is 8cm x 10cm. The Gerber files are included in the Gugussse Compact distribution. Below is a parts list of what you'll need to build it. DigiKey part numbers are included but you can use any parts supplier that can provide the same parts.

gugusse_3.1_pcb_assembly_v1.3.3.pdf

al (al@undisclosed.example.com) — 2025-11-05T11:39:52-0400

gugusse_3.1_pcb_assembly_v1.3.2.pdf - created

al (al@undisclosed.example.com) — 2025-11-05T08:35:42-0400

os_and_software_install_3.03.pdf - created

al (al@undisclosed.example.com) — 2025-11-03T22:50:49-0400

useful_stls

al (al@undisclosed.example.com) — 2025-05-29T11:41:15-0400

This page here contains STLs that are not required for building your Gugusse Compact but you might find the items here practical, if you were looking for the STLs to build the Gugusse Compact, you will find them here: Gugusse Compact. ---------- 35mm film splicer

corekit2.zip - created

al (al@undisclosed.example.com) — 2025-05-29T11:40:11-0400

corekit_screenshot_from_2020-10-19_16-38-58.png - created

al (al@undisclosed.example.com) — 2025-05-29T11:28:42-0400

corekit.zip - created

al (al@undisclosed.example.com) — 2025-05-29T11:17:11-0400

gugusse_roller_usage-250224-v1.1.pdf - created

al (al@undisclosed.example.com) — 2025-03-01T18:36:24-0400

gugusse_3.1_pcb_assembly_v1.3.1.pdf - created

al (al@undisclosed.example.com) — 2024-08-16T15:24:46-0400

opensample00087941.jpg - created

meantux (meantux@undisclosed.example.com) — 2024-06-29T04:42:28-0400

openvs4thirdsvs1dot85.jpg - created

meantux (meantux@undisclosed.example.com) — 2024-06-29T04:42:28-0400

softmatteexample.jpg - created

meantux (meantux@undisclosed.example.com) — 2024-06-29T04:42:27-0400

scopedemo2.jpg - created

meantux (meantux@undisclosed.example.com) — 2024-06-29T04:19:26-0400

scopedemo00088228.jpg - created

meantux (meantux@undisclosed.example.com) — 2024-06-29T04:19:26-0400